Linear position, rotary (angular) position, and tilt sensors by Everight Position, Positek, Netzer, Gill, Zettlex, and Posital
Distributed in North America by:
Everight Position Technologies Corporation
114 Forrest Avenue, Suite 110, Narberth, PA 19072
856-727-9500 or info@evrtp.com

Located outside North America? Click Here

All-In-One Series

GYSE-A Probe

High spec, All-in-one Probe (easy to replace in field with screws)

The GYSE-probe is an all-in-one type sensor with positional resolution up to 1μm. Positon output is Analogue, SSI, or Incremental. Velocity output (option) is avaiable for Analogue type. The positonal difference between 2 magnets can be observable as well. This allows quick and easy sensor cartrige replacement. Sensor parameters (zero, full-scale or range) can be adjusted by using the Windows programming software (ISO9141).

Specifications

Non-linearity < ±0.025%FS (Min .±50μm)
Resolution 16bit (1/65536)
Repeatability ±0.001%FS (Min. ±3 µm)
Temperature Drift < ±20ppm FS/°C
Output Analog
Position Output (Standard) 0-10V (output current: Max.5mA, load: Min.2kΩ) or 4-20mA (load: Min.500Ω)
Velocity Output (Option) ±10V or 4-20mA / Resolution:16bit (1/65536)
Alarm Output Open drain 50V 0.1A (Alarm signal for lost magnet)
Power Supply +24 (±2) VDC (80mA)
Frequency Response Std 1kHz (depending on stroke) sampling
Admissible Pressure 35MPa (Probe rod)
Operating Temperature -20°C-+80°C
Storage Temperature -40°C-+80°C
Vibration 15G(10-2000Hz)
Shock 100G(2msec)
Protection IP67 (Connecting mount or Pigtail type)

Model No.

(1):Effective stroke
15mm-5200mm

(2):Thread
M:M24xP1.0 (Standard)
N:M18xP1.5
U:3/4-16UNF-3A

(3):Sensor rod diameter
blank:Φ10 (Standard)
8:Φ8
14Φ13.8

(4)Cable connection
CN:Connector (Standard)
G*:Pigtail type
(*:Cable length [m], Standard:1.5m)
For CN type, only counter connector supplied.
In case extra cable needed, specify the length.

(5):Analogue position output (OUT1)

AD 0-10V (Standard)
AR 10-0V
BD 4-20mA
BR 20-4mA
CD or CR
bipolar output
[ex]
CD10
CR05
V-V


-10V-+10V
+5V--5V
V Z/F
[ex]
V1/5
V9.5/0.5
Custom order
 
1-5V
9.5-0.5V
I Z/F
[ex]
I5.12/20
I20/5.38
Custom order
 
5.12-20mA
20-5.38mA

*Z=Zero positon

*F=Full scale position

(6):Option:Analogue output (OUT2)
Position:see (5)
Velocity output (Note)
VA[ ] ±10V
WB[ ] 4-20mA
[ ]:max velocity (1.00-999mm/sec)
(ex.9R99:max velocity=9.99mm/sec)
N:No option

(Note)
VA:when magnet stops, output is 0V. when moving toward probe tip, +10V
WB:when magnet stops, output is 4mA. when moving in any direction, 20mA.

Dimensions

Probe

Removing Sensor Element

Connector

Pigtail Type (Option)

Material probe head:Al diecast, probe rod:SS304
Standard magnet:No.2Y.
Other magnets are available from Magnet Grouping [GG].
The tip dead zone length (70mm) depends on the magnet or float type.
Connector:LEMO connector (Material:brass with Ni plating)
(Standard:straight type, Option:L type)

Everight Position Technologies Corporation | 114 Forrest Ave., Suite 110, Narberth, PA 19072 | 856-727-9500 or info@evrtp.com